Previous Page Next Page Prior Version PDF Version Table of Content DFARS Home Page

subpart 246.1--general



 246.101 Definitions.
 246.102 Policy.
 246.103 Contracting office responsibilities.
 246.104 Contract administration office responsibilities.

246.101  Definitions.


“Metrology” is the science of weights and measures used to determine conformance to technical requirements including the development of standards and systems for absolute and relative measurements.


“Quality” means the composite of material attributes including performance features and characteristics of a product or service to satisfy a given need.


“Quality assurance” is a planned and systematic pattern of all actions necessary to provide adequate confidence that adequate technical requirements are established; products and services conform to established technical requirements; and satisfactory performance is achieved.


“Quality audit” is a systematic examination of the acts and decisions with respect to quality in order to independently verify or evaluate the operational requirements of the quality program or the specification or contract requirements of the product or service.


“Quality program” is a program which is developed, planned, and managed to carry out cost-effectively all efforts to effect the quality of materials and services from concept exploration and definition through demonstration and validation, engineering and manufacturing development, production and deployment, and operations and support.


246.102  Policy.

Departments and agencies shall also—


      (1)  Develop and manage a cost effective quality program to ensure that contract performance conforms to specified requirements.  Apply the quality program to all contracts for services and products designed, developed, purchased, produced, stored, distributed, operated, maintained, or disposed of by contractors.


      (2)  Conduct quality audits to ensure the quality of products and services meet contractual requirements.


      (3)  Base the type and extent of Government contract quality assurance actions on the particular acquisition.


      (4)  Provide contractors the maximum flexibility in establishing efficient and effective quality programs to meet contractual requirements.  Contractor quality programs may be modeled on military, commercial, national, or international quality standards.


246.103  Contracting office responsibilities.

The contracting office may conduct product-oriented surveys and evaluations to determine—


      (1)  The adequacy of the technical requirements relating to quality; and


      (2)  Product conformance to design intent.  Consider conducting the surveys and evaluations in conjunction with the activity responsible for technical requirements.


      (a)  Contracting offices are also responsible for—


              (i)  Assisting the technical activity in improving the quality requirements for contracts when first identified for competitive acquisition; and


              (ii)  Assisting in determining the cause of problems noted in user experience reports.


      (b)  The contracting office must coordinate with the quality assurance activity before changing any quality requirement.


      (c)  The activity responsible for technical requirements may prepare instructions covering the type and extent of Government inspections for acquisitions that are complex, have critical applications, or have unusual requirements.


              (i)  In preparing the instructions, the technical activity shall consider, as applicable—


                    (A)  The past quality history of the contractor;


                    (B)  The criticality of the material procured in relation to its intended use, considering such factors as—


                          (1)  Reliability;


                          (2)  Safety;


                          (3)  Interchangeability; and


                          (4)  Maintainability;


                    (C)  Problems encountered in the development of the material;


                    (D)  Problems encountered in other procurements of the same or similar material;


                    (E)  Available feed-back data from contract administration, receiving, testing, or using activities; and


                    (F)  The experience of other contractors in overcoming manufacturing problems.


              (ii)  The instructions shall—


                    (A)  Be kept to a minimum;


                    (B)  Comply with 246.470-2; and


                    (C)  Be prepared on a contract-by-contract basis.
              (iii)  The instructions shall not—


                    (A)  Serve as a substitute for incomplete contract quality requirements;


                    (B)  Impose greater inspection requirements than are in the contract;


                    (C)  Use broad or general designations such as—


                          (1)  All requirements;


                          (2)  All characteristics; or


                          (3)  All characteristics in the classification of defects;


                    (D)  Be used for routine administrative procedures; or


                    (E)  Specify continued inspection requirements when statistically sound sampling will provide an adequate degree of protection.


              (iv)  After issuing the instructions, the technical activity—


                    (A)  Must provide the contract administration office available information regarding those factors which resulted in the requirement for Government inspection;


                    (B)  Must periodically analyze the need to continue, change, or discontinue the instructions; and


                    (C)  Must advise the contract administration office of the results of the periodic analyses.


246.104  Contract administration office responsibilities.


      (f)  The contract administration office shall continue to follow any specific written instructions received from the contracting office until the contracting office acts on a recommendation.




Previous Page Next Page Prior Version PDF Version Table of Content DFARS Home Page